|
|
|
| Apartments
& Condos Senior
Housing Boats
& RVs Professional
Offices Military
Living
|
 |
|
A fully featured line of washer dryer combo units |
 |
| Installation: LG Combo Washer Dryer
|
Innovative Washing's combo washer dryers are very simple to
install and use in your home or business. For a standard installation, you
don’t need anything other than the proper electrical outlet (120 Volts
for the WM3431HW,
WM3431HS, and the WM3677HW),
a cold water and hot water washer connection, and a standpipe to drain to. All
Innovative Washing washer dryer combo units featured use standard connections
when being installed.
If you are going to use your washer dryer combo as a portable unit - that is,
if you are going to store it somewhere when it is not in use and move it out of
storage to use it, you may want to add on a portability kit to your combo. To
read portability kit and accessory installation guides
click here.
|
|
| What You Need:
|
Tools: Level, Utility Knife, Spanner
Water: Washer Dryer needs two standard 3/4 inch water supply
faucets for hot and cold water, with a pressure between 4.5 to 145 pounds per
square inch. You can install your LG washer dryer combs to a single faucet with
hot and cold water supply using the Y Connector accessory.
Electricity: 120 Volts , 60 Hz, 10 Amps
|
| |
| What Is Supplied:
|
| 2 Inlet Water Hoses, 1 Wrench, 2 Washers, 1 Tie Strap , 4
Caps |
| |
| Step 1: Preparing the Washer Dryer Combo
|
- Carefully remove the box and packaging materials from the
outside of the washer dryer.
- The drain hoses and the power cord are secured on the back of the unit.
Please unstrap them.
- Unscrew and remove the four shipping bolts and braces from the back of the
washer dryer with the wrench. Close the holes with the caps provided. Store the
bolts, braces, and wrench in a safe place in case you need to move the washer
dryer in the future.
- Make sure to install the washer dryer combo on a solidly constructed floor.
- Loosen the two front adjustable legs to the desired level and lock nuts with
a spanner.
|
| |
| Step 2: Installation
|
- Place the drain hose in the drain. Do not allow the hose
to kink or get damaged.
- Do not install the drain hose into the drain in an air-tight connection;
ensure there is some airflow possible.
- For best performance the drain hose should not be restricted in any way.
- The drain hose should not be placed higher than 96 inches from the bottom of
the washer dryer.
- Caution must be exercised to avoid collapsing or damaging the drain hose.
- Strap the drain hose to the stand pipe.
- Thread the inlet water hoses to the proper water faucet connections. The
connector for hot water is colored red. Tighten by hand until snug. Turn an
additional 2/3rd turn by pliers.
- Do not overtighten. Make sure the water line connection into the back of the
unit is secure.
- Turn on the water supply. Check all connections for leaks.
- Plug the power cord into a grounded 120V, 60Hz approved electrical service
protected by a fuse or circuit breaker.
- Slide washer dryer into position. Make sure the drain hose remains routed
straight through the clip without collapsing or kinking.
- Level washer dryer by turning the leveling legs in or out as necessary.
- Tighten leg lock nuts.
- The washer dryer must be level on four sides. To properly level use a
carpenters level. It is always a good idea to check for level again after the
first few washes and re-level if necessary. |
| |
| Step 3: Final Check List
|
- Instructions and other items have been removed from the
tub.
- Shipping bolts have been removed.
- Washer dryer is plugged in to an electric outlet and is properly grounded.
- Water hoses are connected to the appropriate faucets with inlet screens and
washers.
- Water is turned on and checked for leaks at faucet and machine end
connections.
- Drain hose is properly located into drain facility and is not collapsed or
damaged.
- Washer dryer has been properly levelled, all legs firmly on the floor and
lock nuts engaged.
- Water fills properly.
- Test for proper operation by running the washer dryer through a complete
cycle. |
|
|
| Having problems? Check out our
FAQs or contact us.
|
|
|
 |
Faucet
Adapter
This faucet adapter allows your LG or EdgeStar washer dryer to connect to any
standard faucet for a water supply. The washer dryer can then drain to the
sink. |
 |
Y
Connector
This Y connector works with a faucet adapter to allow your LG washer dryer to
connect to any standard faucet for a dual line water supply. |
 |
Caster
Wheels
These locking caster wheels replace the leveling legs and allow your LG washer
dryer combo to roll from place to place. |
 |
Dolly
This dolly has attached locking caster wheels and is made to fit perfectly to
your EdgeStar washer dryer combo, allowing you to roll it from place to place. |
|
 |
EdgeStar
Combo
Portability Kit
This kit combines a faucet adapter and dolly with casters to allow your
EdgeStar washer dryer to connect to any standard faucet for a water supply and
be fully portable.
|
 |
LG
Combo
Portability Kit
This kit combines a faucet adapter, Y connector, and rolling casters to allow
your LG washer dryer to connect to any standard faucet for a water supply and
be fully portable.
|
 |
LG
Combo Faucet
Installation Kit
This kit combines a faucet adapter and Y connector to allow your LG washer
dryer combo to connect to any standard faucet for a dual line hot and cold
water supply.
|
|
|
|
|
| At Innovative Washing, we continually strive to satisfy the
needs of our customers in order to develop long-lasting, rewarding
relationships. We place top priority on delivering excellent customer service,
as has been our goal for the past 20 years. Our knowledge and expertise in
combination washer dryer placement is unmatched in the industry. |
Privacy
Policy |
Terms of Service | FAQs |
Site Map
©Copyright 2006 Innovative Washing, Inc. All Rights Reserved. |
|
