Innovative Washing: The Reliable Washer Dryer Combo Experts

Call Us Today For Your Free Quote: 1-866-340-3466

Home

Products

Apartments & Condos Senior Housing Boats & RVs Professional Offices Military Living


	Model CW1200 EdgeStar 110V Ventless Washer Dryer Combo
	Model CW1210V EdgeStar 110V Vented Washer Dryer Combo
	Model CW2200 EdgeStar 220V Ventless Washer Dryer Combo
	Model WM3431HW LG 115V Direct Drive Ventless Washer Dryer Combo
	Model WM3431HS LG 115V Direct Drive Ventless Washer Dryer Combo
	Model WM3677HW LG 120V Direct Drive Ventless Washer Dryer Combo

Innovative Washing Product Guide
A fully featured line of washer dryer combo units

Installation: EdgeStar Combo Washer Dryer

Innovative Washing's combo washer dryers are very simple to install and use in your home or business. For a standard installation, you don’t need anything other than the proper electrical outlet (110 Volts for the CW1200 and CW1210V or 220 Volts for the CW2200), a cold water washer connection, and a standpipe to drain to. All Innovative Washing washer dryer combo units featured use standard connections when being installed.

If you are going to use your washer dryer combo as a portable unit - that is, if you are going to store it somewhere when it is not in use and move it out of storage to use it, you may want to add on a portability kit to your combo. To read portability kit and accessory installation guides click here.

What You Need:

Tools: Screw Driver (Flat Blade), Level, Nut Driver, Channel Lock, Utility Knife, Multi Wrench
Water: Washer Dryer needs one standard 3/4 inch water supply faucet with a pressure between 30 to 120 pounds per square inch
Electricity: Refer to serial plate for specific electrical requirements

What Is Supplied:

1 Inlet Water Hose, 2 Washers

Vented Washer Dryer Vent Pipe Connection (CW1210V) :

- The EdgeStar CW1210V washer dryer expels damp air during the drying period. This damp air must be exhausted outside of the room where the unit is installed
- To properly exhaust the air, screw pipe A into base B in such a manner that the tube is pointed upward
- The exhaust pipe A can not be longer than 2 meters in order to avoid reduction in dryer performance
- The pipe A has to be correctly fitted to the base B in order to avoid leakage during the washing or drying process

Step 1: Preparing the Washer Dryer Combo

- Carefully remove the box and packaging materials from the outside of the washer dryer.
- The drain hose and the power cord are secured on the back of the unit. Please unstrap them.
- Unscrew and remove the four shipping bolts from the back of the washer dryer. Remove the four spacers that the bolts were attached to as well. Store these in a safe place in case you need to move the washer dryer in the future.
- Loosen the two front adjustable legs to the desired level and lock nuts with spanner provided.

Step 2: Installation

- Place the drain hose in the drain. Do not allow the hose to kink or get damaged.
- Do not install the drain hose into the drain in an air-tight connection; ensure there is some airflow possible.
- For best performance the drain hose should not be restricted in any way.
- The drain stand pipe should be not be higher than 2.6 ft and not lower than 1.64 ft.
- Caution must be exercised to avoid collapsing or damaging the drain hose.
- Strap the drain hose to the stand pipe.
- Thread the inlet water hose to your cold water faucet connection. Tighten by hand until snug. Turn an additional 2/3rd turn by pliers.
- Do not overtighten. Make sure the water line connection into the back of the unit is secure.
- Turn on the cold water supply. Check all connections for leaks.
- Plug the power cord into a grounded 60Hz approved electrical service(110V for CW1200 and CW1210V, 220V for CW2200) protected by a 10 amp fuse or a comparable circuit breaker. The washer dryer is grounded through the third prong.
- Slide washer dryer into position. Make sure the drain hose remains routed straight through the clip without collapsing or kinking.
- Level washer dryer by turning the leveling legs in or out as necessary.
- Tighten leg lock nuts.
- The washer dryer must be level on four sides. To properly level use a carpenters level. It is always a good idea to check for level again after the first few washes and re-level if necessary.

Step 3: Final Installation Check List

- Instructions and other items have been removed from the tub.
- Shipping bolts have been removed.
- Washer dryer is plugged in to an electric outlet and is properly grounded.
- Water hose is connected to the faucet with inlet screens and washers.
- Water is turned on and checked for leaks at faucet and machine end connections.
- Drain hose is properly located into drain facility and is not collapsed or damaged.
- Washer dryer has been properly levelled, all legs firmly on the floor and lock nuts engaged.
- Water fills properly.
- Test for proper operation by running the washer dryer through a complete cycle.

Step 4: Test Run

- Prepare your laundry
- Select fabric type and Wash cycle Program. Refer to fabric care label for instructions.
- Load cotton laundry into the drum. Load no more than 6 lbs. of laundry. Do not over load. ( Load unit approximately 2/3 visually full with similar fabrics).
- Load detergent in dispenser 2 for main wash. Follow detergent guide. Use low sudsing detergent.
- Turn Wash Program knob to select the desired wash cycle.
- Press the desired buttons.
- Press dry time button to start drying.
- Press Start.
- Verify washer dryer is filling with water.
- Verify washer dryer stops filling.
- Verify drum is turning and the cycle is ON.
- Verify unit rinses during the rinse cycle.
- Verify unit spins during spin cycle.
- Pull on the door to make sure it does not open.
- Allow the cycle to finish. Release start button to unlock door. (Allow 2-3 minutes for door to unlock).
- Open door, take out laundry.
- Verify laundry is clean and dry. Fold and put away.
- Repeat 1 to 8 for a second cotton load of 6 lbs. Do not overload.
- Press Antiwrinkle button.
- Press Start.
- Check if your clothes are wrinkle free.

Having problems? Check out our FAQs or contact us.

More Information:


	Vented or Ventless?
	Installation
	Purchase Information
	Model Comparison

Accessories:


	Faucet Adapter This faucet adapter allows your LG or EdgeStar washer dryer to connect to any standard faucet for a water supply. The washer dryer can then drain to the sink.
	Y Connector This Y connector works with a faucet adapter to allow your LG washer dryer to connect to any standard faucet for a dual line water supply.
	Caster Wheels These locking caster wheels replace the leveling legs and allow your LG washer dryer combo to roll from place to place.
	Dolly This dolly has attached locking caster wheels and is made to fit perfectly to your EdgeStar washer dryer combo, allowing you to roll it from place to place.

Accessory Kits:


	EdgeStar Combo Portability Kit This kit combines a faucet adapter and dolly with casters to allow your EdgeStar washer dryer to connect to any standard faucet for a water supply and be fully portable.
	LG Combo Portability Kit This kit combines a faucet adapter, Y connector, and rolling casters to allow your LG washer dryer to connect to any standard faucet for a water supply and be fully portable.
	LG Combo Faucet Installation Kit This kit combines a faucet adapter and Y connector to allow your LG washer dryer combo to connect to any standard faucet for a dual line hot and cold water supply.

At Innovative Washing, we continually strive to satisfy the needs of our customers in order to develop long-lasting, rewarding relationships. We place top priority on delivering excellent customer service, as has been our goal for the past 20 years. Our knowledge and expertise in combination washer dryer placement is unmatched in the industry.